Part Number Hot Search : 
EDDTRPB 01701 Z5237 100EL F1603 DREL6 29LV00 K4S64
Product Description
Full Text Search
 

To Download RM3182 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 Electronics
Semiconductor Division
RM3182
ARINC 429 Differential Line Driver
Features
* * * * * * * * Adjustable rise and fall times Adjustable output voltage swing Short circuit protected Output overvoltage protected Sync and clock enable inputs TTL and CMOS compatible inputs MIL-STD-883B types available 100 Kbits/second data rate
Description
The RM3182 consists of a bus interface line driver circuit plus auxiliary gating and synchronization circuitry. Designed to address the ARINC 429 standard, the RM3182 has output rise and fall times adjustable by the selection of two external capacitor values, and the output voltage swing range can be adjusted through an externally applied VREF signal. The logic inputs as well as the sync control inputs are TTL-CMOS compatible. The device is constructed on a monolithic IC using a junction-isolated bipolar process. Sputtered SiCr resistors are used in the internal bias circuitry, providing stable internal bias currents. The RM3182 is available in 16-lead ceramic DIP and 28-pad LCC, and can be ordered with MIL-STD883B high reliability screening.
Block Diagram
V REF (1) +VS (9) CA (5) (6) A OUT
(4) Data (A) (14) Clock (3) Sync (13) Data (B) (16) V1 Power Enable Current Regulator (2) (7) -V S CB (12) Level Shifter And Slope Control (B) Level Shifter And Slope Control (A)
Output Driver (A) R OUT /2 (8) Gnd
RL CL
R OUT /2 Output Driver (B)
B OUT (11)
OverVoltage Clamps
Notes: 1. RL and CL are external. Full load values are: RL = 400, CL = 0.03F. 2. Pin numbers are for 16-lead DIP.
65-3182-01
Rev. 1.0.0
RM3182
PRODUCT SPECIFICATION
Pin Assignments
Sync PWR Enable NC VREF V1 NC NC NC Data (A) NC NC CA NC NC
28 1
Sidebraze DIP
VREF PWR Enable Sync Data (A) CA AOUT -VS GND
1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9
65-3182-02
V1 NC Clock Data (B) CB BOUT NC +VS
LCC
Clock NC Data (B) CB NC NC NC
NC AOUT -VS GND +VS BOUT NC
65-3182-03
Absolute Maximum Ratings
Parameter Supply Voltage (+VS to -VS) V1 Voltage VREF Voltage Logic Input Voltage Output Short Circuit Duration Output Overvoltage Storage Temperature Range Operating Temperature Range (see Note 2) Lead Soldering Temperature (60 sec.)
Notes: 1. Heatsinking may he required for output short circuit at +125C. 2. Heatsinking may be required depending on load and signal frequencies
Min.
Max. 36 +7 +6
Units V V V V V C C C
-0.3 -6.5 -65 -55
+VS + 0.3 See Note 1 +6.5 +150 +125 +300
Thermal Characteristics
(Still air, soldered into PC board) Sidebrazed DIP Maximum Junction Temperature Max. PD TA < 50C Thermal Resistance JC Thermal Resistance JA For TA > 50C Derate at +175C 1470 mW 25C/W 85C/W 11.7 mW/C LCC +175C 1040 mW 25C/W 120C/W 8.3 mW/C
2
PRODUCT SPECIFICATION
RM3182
Electrical Characteristics
(VS = 15V, VREF = V1 = +5V, PWR Enable = 0V, RL = open circuit, -55C TA +125C) Parameters Positive Supply Current Negative Supply Current V1 Supply Current VREF Supply Current Input Logic Level High Input Logic Level Low Output Voltage High Output Voltage Low Output Voltage Null Input Current High Input Current Low Output Short Circuit Current Output Short Circuit Current Positive Supply Current Negative Supply Current Input Capacitance
1
Test Conditlons Data Rate = 0 to 100 Kbits/sec Data Rate = 0 to 100 Kbits/sec Data Rate = 0 to 100 Kbits/sec Data Rate = 0 to 100 Kbits/sec
Min. -16 -1.0 2.0
Typ. 11 -10 200 -0.4
Max. 16 975 -0.15 0.5
Units mA mA A mA V V V V mV A A mA mA mA mA pF
With Respect to Ground With Respect to Ground Both Data Input = Logic 0 VIN = 2.0V VIN = 0.5V Output in High State, to Gnd Output in Low State, to Gnd Output High and Shorted to Gnd Output Low and Shorted to Gnd
4.75 -5.25 -250 -20 80 -150
5.0 -5.0 0 1 -1 -133 133
5.25 -4.75 +250 10 -80 150
5
15
Note: 1. Guaranteed by design.
Typical Power Dissipation Characteristics
(VS = 15V, V1 = VREF = +5V, Pwr Enable = 0V, TA = + 25C) Data Rate (Kbits/sec) 0 to 100 12.5 to 14 100 Positive Supply Current 11 mA 24 mA 46 mA
1 1
Load Open Circuit Full Load Full Load
Negative Supply Current -10 mA -24 mA -46 mA
Pin V1 Supply Current 200 A 200 A 200 A
Internal Power Dissipatlon 325 mW 660 mW 1000 mW
Load Power Dissipatlon 0 60 mW 325 mW
Note: 1. RL = 400, CL = 0.03 F (see Block Diagram).
3
RM3182
PRODUCT SPECIFICATION
Principles of Operation
Each device consists of one differential driver and associated gating circuitry. The gating circuitry consists of clock and sync signal inputs which are ANDed with the two data inputs. See the block diagram and truth table. Three power supplies are required to operate the RM3182 in a typical ARINC 429 bus application: +15V, -15V, and +5V. The +5V supply, in addition to powering the internal bus current regulator, provides a reference voltage that determines the output voltage swing. The differential output swing will equal 2 VREF. If a value of VREF other than +5V is used, then a separate +5V supply is required for pin V1. Figure 1 depicts connections for the ARINC 429 application. The driver output impedance is nominally 75. With the Data(A) input at a logic high and Data (B) input at a logic
low, AOUT will swing to +VREF and BOUT will swing to VREF (constituting a logic high state). Reversing the data input states will cause AOUT to swing to -VREF and BOUT to +VREF. With both data input signals at a logic low state, the outputs will both swing to 0V (output in null state). The slew rate of the outputs, and consequently rise and fall times, can be adjusted through the selection of two external capacitor values. Typical values are CA = CB = 75 pF for high-speed operation (100 Kbits/sec) and CA = CB = 500 pF for low-speed operation (12.5 to 14 Kbits/sec). The device can be powered down by applying a logic high signal to the Power Enable pin. If the power down feature is not used, then the Power Enable pin should be tied directly to ground.
+5V
+15V
1 V REF 16 4 V1 Data (A) 3 Sync 14 9 +V S RM3182 Inputs Power Enable Data (B) Gnd CB 8 CA 12 5 Note: Pin numbers are for the 16-lead DIP. 2 -VS 7 11 B OUT 6 A OUT To Bus Clock
13
-15V
65-3182-04
Figure 1. ARINC 429 Bus Application
4
PRODUCT SPECIFICATION
RM3182
Data A Data B
0V
0V +VREF Adjust By CB or Rate Select
Out A or Amp A Adjust By CA or Rate Select Out B or Amp B
-VREF +V REF
-VREF High = +VREF
Differential Output
Out A- Out B or Amp Out AAmp Out B
0V
Null
Low = -VREF Note: Outputs unloaded
65-3182-05
Figure 1. Switching Waveforms
Truth Table
Sync X L H H H H Clock L X H H H H Data (A) X X L L H H Data (B) X X L H L H AOUT 0V 0V 0V -VREF +VREF 0V BOUT 0V 0V 0V +VREF -VREF 0V Comments Null Null Null Low High Null
5
RM3182
PRODUCT SPECIFICATION
Mechanical Dimensions
16-Lead Sidebraze DIP
Inches Min. A b1 b2 c1 D E e eA L L1 Q s1 s2 Max. Millimeters Min. Max. 7 2 7 Notes: Notes 1. Index area: a notch or a pin one identification mark shall be located adjacent to pin one. The manufacturer's identification shall not be used as pin one identification mark. 2. The minimum limit for dimension "b2" may be .023 (.58mm) for leads number 1, 8, 9 and 16 only. 3. Dimension "Q" shall be measured from the seating plane to the base plane. 4. The basic pin spacing is .100 (2.54mm) between centerlines. Each pin centerline shall be located within .010 (.25mm) of its exact longitudinal position relative to pins 1 and 16. 5. Applies to all four corners (leads number 1, 8, 9, and 16). 6. "eA" shall be measured at the centerline of the leads. 3 5 7. All leads - Increase maximum limit by .003 (.08mm) measured at the center of the flat, when lead finish applied. 8. Fourteen spaces.
Symbol
-- .200 .014 .023 .045 .065 .008 .015 -- .860 .280 .310 .100 BSC .300 BSC .125 .200 .140 -- .015 .070 .005 -- .005 --
-- 5.08 .36 .58 1.14 1.65 .20 .38 -- 21.84 7.11 7.87 2.54 BSC 7.62 BSC 3.18 5.08 3.56 -- .38 1.78 .13 -- .13 --
4, 8 6
D
8 1
NOTE 1
E
9
16
s1 S2 eA
A Q L b2 b1 e L1
c1
6
PRODUCT SPECIFICATION
RM3182
Mechanical Dimensions (continued)
28 Terminal Leadless Chip Carrier (LCC)
Inches Min. A A1 B1 B3 D/E D1/E1 D2/E2 e h j L1 L2 L3 ND/NE N .060 .050 .022 .006 Max. .100 .088 .028 .022 Millimeters Min. 1.52 1.27 .56 .15 Max. 2.54 2.24 .71 .56 3, 6 3, 6 2 2, 5 Notes: Notes 1. The index feature for terminal 1 identification, optical orientation or handling purposes, shall be within the shaded index areas shown on planes 1 and 2. Plane 1 terminal 1 identification may be an extension of the length of the metallized terminal which shall not be wider than the B1 dimension. 2. Unless otherwise specified, a minimum clearance of .015 inch (0.38mm) shall be maintained between all metallized features (e.g., lid, castellations, terminals, thermal pads, etc.). 3. Dimension "A" controls the overall package thickness. The maximum "A" dimension is the package height before being solder dipped. 4 4 4. The corner shape (square, notch, radius, etc.) may vary at the manufacturer's option, from that shown on the drawing. The index corner shall be clearly unique. 5. Dimension "B3" minimum and "L3" minimum and the appropriately derived castellation length define an unobstructed three dimensional space traversing all of the ceramic layers in which a castellation was designed. Dimension "B3" maximum and "L3" maximum define the maximum width and depth of the castellation at any point on its surface. Measurement of these dimensions may be made prior to solder dripping. 6. Chip carriers shall be constructed of a minimum of two ceramic layers.
Symbol
.442 .460 .300 BSC .150 BSC .050 BSC .040 REF .020 REF .045 .075 .003 7 28 .055 .095 .015
11.23 11.68 7.62 BSC 3.81 BSC 1.27 BSC 1.02 REF .51 REF 1.14 1.91 .08 7 28 1.40 2.41 .38
5
LID See Note 1 D
PLANE 2 A1
PLANE 1
L3
B1 E DETAIL "A"
B3
A Index Corner (j) x 45 (h) x 45 4 3 PLCS DETAIL "A" D2 D1 e
L2
L1
7
PRODUCT SPECIFICATION
RM3182
Ordering Information
Part Number RM3182S RM8182S/883B RM3182L RM3182L/883B
Notes: /883B suffix denotes MIL-STD-883, Level B processing S = 16 Lead sidebraze ceramic DIP L = 28 Terminal Leadless Chip Carrier
Package S S L L
Operating Temperature Range -55C to +125C -55C to +125C -55C to +125C -55C to +125C
The information contained in this data sheet has been carefully compiled; however, it shall not by implication or otherwise become part of the terms and conditions of any subsequent sale. Raytheon's liability shall be determined solely by its standard terms and conditions of sale. No representation as to application or use or that the circuits are either licensed or free from patent infringement is intended or implied. Raytheon reserves the right to change the circuitry and any other data at any time without notice and assumes no liability for errors.
LIFE SUPPORT POLICY:
Raytheon's products are not designed for use in life support applications, wherein a failure or malfunction of the component can reasonably be expected to result in personal injury. The user of Raytheon components in life support applications assumes all risk of such use and indemnifies Raytheon Company against all damages. Raytheon Electronics Semiconductor Division 350 Ellis Street Mountain View, CA 94043 650.968.9211 FAX 650.966.7742
8/97 0.0m Stock# DS30003182 (c) Raytheon Company 1997


▲Up To Search▲   

 
Price & Availability of RM3182

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X